BLTouch for Ender 3 MINIMAL breakout
**********IMPORTANT***********
new revison available
If the cable that comes with your BLTouch has a fixed 1x3 wire block for attaching to the breakout pins, then you need to swap the 5V and GND around.
see this video: https://youtu.be/ocAeZRPVusw?t=341
otherwise if you have seperate du-pont style connectors then attach (or solder directly) the wires making sure 5V and GND goes to the correct marked Pins.
I have made a new revision of this board at https://www.pcbway.com/project/shareproject/BLTouch_ender3_minimal.html where the 5V and GND pins are swapped so you don't have to mod the cable or use individual dupont extenders .
Description
A minimal breakout Pin 27 for the Ender 3 3D printer to use the BLTouch auto leveler with just a stacking long pin female 2x5 2.54mm header block and a strip of 3 2.54mm header pins.
Components
Use a long pin 2x5 2.54" stackable female header block and a 1x3 strip of header pins (or right angle pins) to breakout Pin 27 for the Ender 3 3D printer to use the BLTouch auto leveler.
the stacking header pins insert through from the bottom (no silkscreen labels) so that the LCD plug attaches on the label side. it's a passthrough so you connect it exactly as if the board wasn't there at all
NOTE!
Use caution with this board as none of the parts are keyed!
BLTouch for Ender 3 MINIMAL breakout
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Al The Dude
- PiStorm Tester ZZ9 Plural Z Alpha PiStorm Tester is a PCB that exposes all the IO's of the 68000 DIP64 socket that PiStorm uses. There...
- BLTouch-ender3-minimal DescriptionA minimal breakout Pin 27 for the Ender 3 3D printer to use the BLTouch auto leveler with...
- BLTouch for Ender 3 MINIMAL breakout **********IMPORTANT*********** new revison availableIf the cable that comes with your BLTouch has a ...
- Ender 3 BLTouch adapter **********IMPORTANT*********** (Do not order, there's a new revison available ( here )- unless ...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
471 0 0 -
RF Control training board for students based on ESP32 C3
628 0 2 -
Aquarius+ Computer, Standard PCB
837 0 4 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
586 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
506 0 1 -
Nintendo Famicom HVC-001 Controller Shells
609 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
561 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
759 1 5 -