Ender 3 BLTouch adapter
**********IMPORTANT*********** (Do not order, there's a new revison available ( here )- unless you take note of the following info)
If the cable that comes with your BLTouch has a fixed 1x3 wire block for attaching to the breakout pins, then you need to swap the 5V and GND around.
see this video: https://youtu.be/ocAeZRPVusw?t=341
otherwise if you have seperate du-pont style connectors then attach (or solder directly) the wires making sure 5V and GND goes to the correct marked Pins.
I will create a new revision soon with the pins the right way round.
Description
A simple board to adapt a BLtouch into an ender 3 without splicing cables
Required Ccomponents
H1: 1x 2x5 2.54mm pitch female header socket
P1: 1x 2x5 2.54mm IDC male receptacle
CN1: 1x 1x3 2.54mm JST XH receptacle or header pins
Add the IDC and XH receptacles to the silkscreen side and the female header to the underside and voilla! you have a passthrough with a tap into GPIO 27 (Sig) and a 5V, GND to power the BLTouch
Ender 3 BLTouch adapter
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(2)
- Likes(3)
- Engineer Jun 14,2019
- Engineer Jan 30,2019
- Aleksey Jurchenko Dec 29,2018
- 2 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
-
10design
-
10usability
-
5creativity
-
10content
More by Al The Dude
- PiStorm Tester ZZ9 Plural Z Alpha PiStorm Tester is a PCB that exposes all the IO's of the 68000 DIP64 socket that PiStorm uses. There...
- BLTouch-ender3-minimal DescriptionA minimal breakout Pin 27 for the Ender 3 3D printer to use the BLTouch auto leveler with...
- BLTouch for Ender 3 MINIMAL breakout **********IMPORTANT*********** new revison availableIf the cable that comes with your BLTouch has a ...
- Ender 3 BLTouch adapter **********IMPORTANT*********** (Do not order, there's a new revison available ( here )- unless ...
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
346 0 0 -
RF Control training board for students based on ESP32 C3
464 0 2 -
Aquarius+ Computer, Standard PCB
659 0 3 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
478 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
422 0 0 -
Nintendo Famicom HVC-001 Controller Shells
517 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
493 0 4 -
COMMODORE 128 15KHz DISPLAY ADAPTER (C128 80 COLUMN ADAPTER)
631 1 4 -