|
KiCADKicad
|
|
|
FreeCADFree Software Foundation, Inc.
|
Warm Floater Eurorack Power Extender
I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outputs for eurorack power (2x8 2.54mm, +/- 12V, 5V, gate, control), so it's a 1 to 3 adapter.
Check your 3 modules' current draw before using it, as 3 hefty modules may strain your rack's power supply.
For low current draw modules this can be a very helpful board.
I include KICAD files, the gerber, and the files you'll need to 3D print the "cradle" for it in the project files below.
Read more about this project in this AudioDiWHY blog post: https://audiodiwhy.blogspot.com/2023/11/warm-floater-eurorack-power-strip.html.
NOTES:
For the 3D print, even after careful measurements and double checking FreeCAD's dimensions I still needed to scale my 3D print to102%. At 100% the board was a very tight fit. My 3D printer usually prints a bit small however.
Warm Floater Eurorack Power Extender
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by AudioDIWHY
- Vactrol Based Audio Envelope Follower An audio envelope follower based on a 5C3 Vactrol.Eurorack format--6HP. Uses +/- 12V at about 20mA p...
- Warm Floater Eurorack Power Extender I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
- "KiCADSR" Euro Envelope Generator This is my first project using KiCAD for EDA instead of Autodesk Eagle. I wanted to see if I had the...
- Low Noise Preamp based on Arp 2600 Synthesizer The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
- Arp 2600 clone--inverter-mixer The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
- SEEED XAIO RP2040 ADC and Buffer Board The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
- Anything to Clock--LM311 based If you need a precision rectifier to turn audio or LFO signals into clock, this small circuit gets t...
- Anything to Clock--Precision Rectifier For more details please see this blog post:https://audiodiwhy.blogspot.com/2024/04/anything-to-clock...
- Hardware Encoder Debounce Board For details about this project please see this blog post: https://audiodiwhy.blogspot.com/2024/01/ro...
- DSPG1 4 voice synthesizer on a single PCB The DSPG1 is a $20 IC--along with a handful of external parts this chip gives you a complete a 4 voi...
- Son of Warm Floater I ran out of power spigots in my Eurorack, this simple project takes a 16 conductor +/- 12V, GND, 5V...
- ARP 2600 Audio Switch The legendary ARP2600 has a pop free/click free clock driven analog switch. Each rising clock switch...
- DG401 Audio CMOS switch Experimenter's Board I was curious how the DGx0x series analog switches sounded and didn't want to breadboard a DG401 wit...
- ARP2600 Lag Processor Clone The Arp 2600 "Voltage Processor" section is one of the many designs that makes this legendary synth ...
- Eurorack Bench Mixer I needed a bench mixer for my Eurorack workbench setup--to replace the Frac-formatted audio bench ge...
- Dual Korg MS20 VCF for Eurorack Build your own Dual MS20 VCF....this is Euro format, 15HP, +/-12V.This project requires 2 of the PCB...
- MS20 Clone Voltage Controlled Filter The Korg MS20 is a lengendary semi-modular monophonic synthesizer. The PCB here is the MS20's VCF l...
- RP2040-AD9833 based Volt-octave Synthesizer VCO Can a Eurorack analog-sounding audio volt per octave VCO be built using an RP2040 MCU and AD9833 bre...
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
613 0 0 -
RF Control training board for students based on ESP32 C3
791 0 2 -
Aquarius+ Computer, Standard PCB
1043 0 5 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
669 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
576 0 1 -
Nintendo Famicom HVC-001 Controller Shells
687 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
647 0 4