Low Power Continuity Tester
Low Power Continuity Tester
Board Size 50.5mm x 20mm,
Low power : Should run a decent amount on time on a single CR2032 cell.
Fully featured :
Low voltage continuity test mode : Compliance voltage < 0.5v, low current.
Inverse continuity mode : Beep if continuity is broken.
Both modes with "latching" glitch capture: start beeping immediately and keep beeping for at least a split second.
Diode test mode : Short beep on forward voltage within diode drop (0.1-0.7v), continuous beep on short circuit.
Simple to use : no power switch, turn on by touching probes, mode switch with a single button.
Low cost
Low Power Continuity Tester is Jose Ignacio Romero project
for more details please visit :
https://hackaday.io/project/8467-low-power-continuity-tester#j-discussions-title
Low Power Continuity Tester
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by pohokanapoe MV
- USB Power Filter USB Power FilterThe USB Power Filter reduces noise and ripple on the 5V power rail through a combina...
- Single Channel Ignition Coil Driver Single Channel Ignition Coil DriverSingle Universal Ignition Control Module for dumb ignition coils ...
- Dual VR Conditioner (Mini) Dual VR Conditioner v3.x (mini size) for SpeeduinoA plug in module to allow your ECU to condition th...
- Dual Channel Ignition Coil Driver Dual Channel Ignition Coil DriverDual Universal Ignition Control Module for dumb ignition coils (not...
- MSOP-8 to DIP-8 Adapter MSOP-8 to DIP-8 AdapterBoard Size 11mm x 11mmAttention : Don't populate MSOP-8 with thermal/exposed ...
- SOIC-8 to DIP-8 Adapter Standard SOIC-8 to DIP-8 AdapterBoard size 11mm x 11mmSOIC-8DIP-8
- Dual VR Conditioner + Regulator Dual VR Conditioner with optional 5V Voltage RegulatorI change some THT to SMT package and add capac...
- Low Power Continuity Tester Low Power Continuity TesterBoard Size 50.5mm x 20mm,Low power : Should run a decent amount on time o...
- Tiny Remote Tiny Remote - IR Remote Control based on ATtiny13A v1.1 by Stefan WagnerBoard size 43x94mm, I'm usin...
- Dual VR Conditioner v3.x for Speeduino A plug in module to allow your ECU to condition the AC signal from a VR Crank/Cam sensor to DC for y...
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
615 0 0 -
RF Control training board for students based on ESP32 C3
794 0 2 -
Aquarius+ Computer, Standard PCB
1047 0 6 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
670 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
579 0 1 -
Nintendo Famicom HVC-001 Controller Shells
687 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
647 0 4