|
EagleAutodesk
|
Eurorack SEM style Attenuverter
Attenuverters are critical to modern modular synthesis and are found in classic modules by Make Noise, Mutable Instruments and the like.
They have been around for a long time; I first saw them used in the late 70's in an instrument called an Oberheim SEM, which is now considered a classic.
I did some research on the attenuverter subcircuit in the SEM and contacted Tom Oberheim directly to gain insight as to why his attenuverter design is so musical and user friendly.
To my astonishment Mr. Oberhiem emailed me back!
At the core of Tom's design is a somewhat unusual component--a Center Tap Pot. This is a potentiometer with the center of the resistive element brought to a 4th solder pin which you can connect to ground.
Fortunately this somewhat unusual part is still readily available from major electronics retailers.
So, here we have a center tap pot attenuverter inspired by the Oberheim SEM, with some extra features, such as voltage control of the output signal's DC offset. It is compliant with the Eurorack standard: 4HP; +/-12V; Skiff depth, and so on.
The module requires 3 PCBs: main board, front panel, and standoff board for the ALPs center tap pot.
if you build this module I suggest making the front panel in black with white silks.
You can get more information from the blog post: https://audiodiwhy.blogspot.com/2022/10/euro-sem-style-attenuverter.html
I include below eagle files, PDFs; a zip of all Gerbers and so on. Note that the main PCB uses 2x SOIC SMD parts (the op amps) but I don't find those too hard to solder--tape them down, use flux and a fine tip on your iron, and be patient. The rest of the components are through hole.
Have fun building!
Eurorack SEM style Attenuverter
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 1 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
More by AudioDIWHY
- Vactrol Based Audio Envelope Follower An audio envelope follower based on a 5C3 Vactrol.Eurorack format--6HP. Uses +/- 12V at about 20mA p...
- Warm Floater Eurorack Power Extender I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
- "KiCADSR" Euro Envelope Generator This is my first project using KiCAD for EDA instead of Autodesk Eagle. I wanted to see if I had the...
- Low Noise Preamp based on Arp 2600 Synthesizer The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
- Arp 2600 clone--inverter-mixer The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
- SEEED XAIO RP2040 ADC and Buffer Board The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
- Anything to Clock--LM311 based If you need a precision rectifier to turn audio or LFO signals into clock, this small circuit gets t...
- Anything to Clock--Precision Rectifier For more details please see this blog post:https://audiodiwhy.blogspot.com/2024/04/anything-to-clock...
- Hardware Encoder Debounce Board For details about this project please see this blog post: https://audiodiwhy.blogspot.com/2024/01/ro...
- DSPG1 4 voice synthesizer on a single PCB The DSPG1 is a $20 IC--along with a handful of external parts this chip gives you a complete a 4 voi...
- Son of Warm Floater I ran out of power spigots in my Eurorack, this simple project takes a 16 conductor +/- 12V, GND, 5V...
- ARP 2600 Audio Switch The legendary ARP2600 has a pop free/click free clock driven analog switch. Each rising clock switch...
- DG401 Audio CMOS switch Experimenter's Board I was curious how the DGx0x series analog switches sounded and didn't want to breadboard a DG401 wit...
- ARP2600 Lag Processor Clone The Arp 2600 "Voltage Processor" section is one of the many designs that makes this legendary synth ...
- Eurorack Bench Mixer I needed a bench mixer for my Eurorack workbench setup--to replace the Frac-formatted audio bench ge...
- Dual Korg MS20 VCF for Eurorack Build your own Dual MS20 VCF....this is Euro format, 15HP, +/-12V.This project requires 2 of the PCB...
- MS20 Clone Voltage Controlled Filter The Korg MS20 is a lengendary semi-modular monophonic synthesizer. The PCB here is the MS20's VCF l...
- RP2040-AD9833 based Volt-octave Synthesizer VCO Can a Eurorack analog-sounding audio volt per octave VCO be built using an RP2040 MCU and AD9833 bre...
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
596 0 0 -
RF Control training board for students based on ESP32 C3
781 0 2 -
Aquarius+ Computer, Standard PCB
1032 0 5 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
665 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
573 0 1 -
Nintendo Famicom HVC-001 Controller Shells
684 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
642 0 4