|
EagleAutodesk
|
Eurorack Moog CP3 Clone Mixer
Moog CP3 is an classic synthesizer circuit, it adds subtle, warm "minimoog" distortion to your Eurorack modular audio synthesizer.
Some think this mixer design gives vintage moog instruments their classic "fat" sound.
Presented here is a 3 PCB design for Eurorack skiff (+/- 12V power, 3.5mm jacks; less then 30mm deep).
You will need 3 boards to build the entire design,a front panel, a board for pots and jacks, and the mixer PCB.
This community project page provides the gerber for the main board, but again there are 3 boards for this design.
Get all 3 gerbers (front panel, mixer, mixer pots board, all in ZIP format) as well as PDF of layout, schematics, etc., from the cslammy Github repository: https://github.com/cslammy/CP3 or in a zip file in this community project posting.
You can read more about the design and build at this blog post: https://audiodiwhy.blogspot.com/2022/09/cloning-moog-cp3-mixer.html
Eurorack Moog CP3 Clone Mixer
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(4)
- Engineer Jan 22,2024
- Holger OnkelHolgi Aug 18,2023
- Engineer Jul 30,2023
- Engineer May 03,2023
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by AudioDIWHY
- Vactrol Based Audio Envelope Follower An audio envelope follower based on a 5C3 Vactrol.Eurorack format--6HP. Uses +/- 12V at about 20mA p...
- Warm Floater Eurorack Power Extender I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
- "KiCADSR" Euro Envelope Generator This is my first project using KiCAD for EDA instead of Autodesk Eagle. I wanted to see if I had the...
- Low Noise Preamp based on Arp 2600 Synthesizer The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
- Arp 2600 clone--inverter-mixer The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
- SEEED XAIO RP2040 ADC and Buffer Board The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
- Anything to Clock--LM311 based If you need a precision rectifier to turn audio or LFO signals into clock, this small circuit gets t...
- Anything to Clock--Precision Rectifier For more details please see this blog post:https://audiodiwhy.blogspot.com/2024/04/anything-to-clock...
- Hardware Encoder Debounce Board For details about this project please see this blog post: https://audiodiwhy.blogspot.com/2024/01/ro...
- DSPG1 4 voice synthesizer on a single PCB The DSPG1 is a $20 IC--along with a handful of external parts this chip gives you a complete a 4 voi...
- Son of Warm Floater I ran out of power spigots in my Eurorack, this simple project takes a 16 conductor +/- 12V, GND, 5V...
- ARP 2600 Audio Switch The legendary ARP2600 has a pop free/click free clock driven analog switch. Each rising clock switch...
- DG401 Audio CMOS switch Experimenter's Board I was curious how the DGx0x series analog switches sounded and didn't want to breadboard a DG401 wit...
- ARP2600 Lag Processor Clone The Arp 2600 "Voltage Processor" section is one of the many designs that makes this legendary synth ...
- Eurorack Bench Mixer I needed a bench mixer for my Eurorack workbench setup--to replace the Frac-formatted audio bench ge...
- Dual Korg MS20 VCF for Eurorack Build your own Dual MS20 VCF....this is Euro format, 15HP, +/-12V.This project requires 2 of the PCB...
- MS20 Clone Voltage Controlled Filter The Korg MS20 is a lengendary semi-modular monophonic synthesizer. The PCB here is the MS20's VCF l...
- RP2040-AD9833 based Volt-octave Synthesizer VCO Can a Eurorack analog-sounding audio volt per octave VCO be built using an RP2040 MCU and AD9833 bre...
-
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
654 0 0 -
RF Control training board for students based on ESP32 C3
838 0 2 -
Aquarius+ Computer, Standard PCB
1104 0 7 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
705 0 2 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
605 0 1