"FamiCoun" Famicom Front Expansion NES/SNES Controller Adapter
Original GITHUB: https://github.com/jeffqchen/FamiCoun-Famicom-Front-Expansion-NES-SNES-Adapter
"FamiCoun" Famicom Front Expansion NES/SNES Controller Adapter
Here is my design of an expansion to connect NES and SNES controller to the front port of a Nintendo Famicom.
It makes the Famicom look like a Countach in the front. Hence the name of this project.
The player 2 NES port supports the Zapper, as shown on the shell.
Note when you use a SNES controler, Y is B and B is A.
PARTS
Pins
- PCB
- [22x or 28x] Front Pins - Terminal Pins, Male, Machined - Part Number No. 3149-2-00-15-00-00-08-0
- [9x] Back Pins - Terminal Pins, Female, Machined - Part Number No. 170-202-170L003 or 1599600
- [2x] M2x16mm Hex Screw & Nut
- 3D Printed Shell
3D Printing
Print the front jacket, the plugs and the back. The orientation should be pretty self-explanatory when you put them into the slicer.
Support is required for the front jacket.
After the print is done, make sure you enlarge the holes for the NES plugs with a 9/64 drill bit, so plugs can go in properly. I suggest doing it manually since it's easy to overshoot and destroy the smaller holes at the bottom. All this is because if I made the holes any bigger, the slicers would refuse to generate a smooth wall and make the hole not round.
A different version of the front jacket is provided with a holder design for the cover you take off from the Famicom, so you don't end up losing the original cover easily (however if you already lost yours, you can print a new one. I uploaded a design a while back.)
Assembly
Soldering is pretty straightforward. You can use the printed parts to help holding the pins in place and then solder. Just don't let the iron stay on the PCB for too long or you might melt the printed parts.
Note you don't have to populate all the pins, but it makes it look better.
Put the plugs part over the front side through the pins, then seat the assembly into the front jacket piece.
Finally, close it up with the back piece and secure with two sets of M2x16mm screws and nuts.
Misc
Thingiverse Design
- https://www.thingiverse.com/thing:4671897
Special Thanks
- Chris Kempson
- http://chriskempson.com/posts/nes-controller-to-famicom-adapter/
NesDev Wiki
- https://wiki.nesdev.com
Mike Chi, Creator of the Famous RetroTink)
- https://www.retrotink.com
Shield:
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
"FamiCoun" Famicom Front Expansion NES/SNES Controller Adapter
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(3)
- Engineer Mar 19,2024
- Allan Rose Feb 04,2024
- Francisco Meza Feb 04,2024
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Nicolas The Wizard
- SNES2ATARI V2 for Atari 7800 GITHUB: https://github.com/nsinav/SNES2AtariThis is a working project. Games must be specifically co...
- Atari 7800 - A78 Super Cart (Work in Progress) ORIGINAL GITHUB: https://github.com/tdididit/a78-supercart
- Atari 7800 - A78 Simple Cart Original GITHUB: https://github.com/tdididit/a78-simplecart
- Atari 7800 - A78 SD Cart Original GITHUB: https://github.com/tdididit/a78-sdcart
- Atari 7800 - A78 Flashcart Plus Original GITHUB: https://github.com/tdididit/a78-flashcartplus
- Atari 7800 - A78 Flashcart Original GITHUB: https://github.com/tdididit/a78-flashcart
- Necroware's XT Prototyping Board Original GITHUB: https://github.com/necroware/xt-prototyping-board
- Necroware's MCE Adapter 02/2024 rev. GITHUB: https://github.com/necroware/mce-adapterYoutube Video: https://www.youtube.com/watch?v=f9ryi...
- Colecovision 8K/16K/24K/32K Cartridge Features:Create 8K, 16K, 24K and 32K Cartridge games for the Colecovision system.Uses easily availab...
- Atari 5200 16K/32K Cartridge Features:Create 16K and 32K Cartridge games for the Atari 5200 system.Uses easily available, off-the...
- Atari 2600 64K Bankswitch Cartridge Features:Create 64K Cartridge games for the Atari 2600 system.Supports standard Atari F2 (64k) banks...
- Atari 2600 8K / 16K / 32K Activision Bankswitch Cartridge Features:Create 8K, 16K and 32K Cartridge games for the Atari 2600 system.Supports standard Atari F8...
- Atari 2600 8K / 16K / 32K Bankswitch Cartridge Features:Create 8K, 16K and 32K Cartridge games for the Atari 2600 system.Supports standard Atari F8...
- Atari 2600 2K / 4K Activision Cartridge ORIGINAL WEBSITE: https://grandideastudio.com/portfolio/gaming/pixels-past/Features:Supports 2K and ...
- Atari 2600 2K / 4K Classic Cartridge ORIGINAL WEBSITE: https://grandideastudio.com/portfolio/gaming/pixels-past/Features:Supports 2K and ...
- A8 Pico Cart v1.0 3D Case A8 Pico Cart v1.0 3D CaseOriginal GITHUB: https://github.com/robinhedwards/A8PicoCart
- A8 Pico Cart v1.0 - XL/XE Version (Fits Case v1.0) A8 Pico Cart v1.0 - XL/XE Version (Fits Case v1.0)Original GITHUB: https://github.com/robinhedwards/...
- Pico Cart 64 v1 Lite ORIGINAL GITHUB: https://github.com/kbeckmann/PicoCart64SRAM chip supporting ROMs up to 64MB, a WiFi...
-
Naruto Multi-color PCB printed with UV technology
34 2 1 -
-
-
-
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
677 0 0