STK465 Amplifier+Preamp
This is my DIY project try re-make legend IC amplifier STK465 that usually used in branded amplifier such as sansui and others, with the addition of an pre-amplifier using DIP-8 Op-amp.
The sound quality is very detail and clarity with soft bass production, it is above LM1875 and around LM3886 gainclone.
DON'T FORGET to connect the two of input ground on pcb board and with your signal ground to make it low noise.
This amplifier deliver power about 2X30Watt stereo according to the datasheet.
It needs symmetrical transformer 24-0-24 about 5-10Ampere.
The design is standart with addition of preamp that use components easily found on the market.
what does it sounds like?
please check the video til end on Barlex Respectaizer youtube channel
STK465 Amplifier+Preamp
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(3)
- Likes(1)
- Engineer May 03,2021
- 2 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
-
9design
-
10usability
-
10creativity
-
10content
More by barita
- Simple audio limiter This limiter circuit use to avoid clips on a mid-power amp.It controll and decrease the input of amp...
- TIP 41/42 Mini Amplifier SMD The project uses TIP41/42 as the final amplifier, the circuit is made as simple as possible with SMD...
- STEREO AMPLIFIER TPA3255 CLASS D Simple powerfull class D amplifier using TPA3255 chip.This amplifier can produces power up to 2x315W...
- Digital active cross over 2.1 This is a simple 2.1 digital active cross over using PT2353H chip.This active cross over have some m...
- Stereo TDA7266 Mini Amplifier This TDA7266 Chip Amplifier can produce 14Watt Stereo power (2x7Watt) with a single supply 12V
- STK4152 AMPLIFIER Without Tone This board for STK4152II Stereo amplifier. You can also use the other STK41X2 Chip with this board, ...
- Stereo TDA7377 Amplifier TDA7377 Sereo Standart
- Stereo class T Amplifier Class T amplifiers are known for their good sound and high efficiency.The chip I use is TA2020-020 w...
- 5.1 Amplifier using TDA7297 In this project I made a 5.1 amp to be connected to a PC soundcard, later it can be used to watch or...
- uPC1188h Stereo Amplifier In this project I make stereo amplifier 2x20Watt using uPC1188h chip amp.This chip is usually used i...
- 2 Axis Laser CNC Shield This cnc shield for use with arduino uno and motor driver A4988
- Simple mixer for home recording In this project I make a very simple mixer for home recording.You can use this mini mixer for record...
- LA4628 Stereo amplifier This LA4628 chip amp produce a good timbre, clear detail, and natural sound.The components are easy ...
- Karaoke Tone controll V2 In this project I want to make the latest version of the tone control for karaoke, namely karaoke to...
- TA8231L STEREO AMPLIFIER This amp has a simple design but can still be used with audio grade components.Use the potentiometer...
- 2.1 Amplifier TEA2025 This 2.1 amplifier uses TEA2025, one of the cheapest IC chips that is easily available on the market...
- Simple Symmetrical Power Supply General Purposes Symmetrical power supply with 8 Pcs electrolytic capacitor
- 2.1 Pre-amplifier with adjustable Cross Over 30Hz - 150Hz In this project I make 2.1 pre amplifier with adjustable cross over from 30Hz up to 150Hz.The subwoo...
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
568 0 0 -
RF Control training board for students based on ESP32 C3
759 0 2 -
Aquarius+ Computer, Standard PCB
1002 0 5 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
655 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
560 0 1 -
Nintendo Famicom HVC-001 Controller Shells
676 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
628 0 4